• Home
  • 3585-8CN500 Tanged Locking Insert

3585-8CN500 Tanged Locking Insert

SKU: 02856 | MPN: 3585-8CN500
/ Eaches
Subtotal:$0.72
Quantity Available *
QuantityLocation
238Ellisville
WARNING: Cancer and Reproductive Harm --
P65Warnings.ca.gov
Discount by: unit
QuantityPrice
1 - 249
250 - 499
500 - 999
1,000 - 2,999
3,000 - 4,999
5,000 - 9,999
10,000 - 24,999
25,000 - 49,999
50,000 +
*Additional inventory may be available. Please contact your sales location.

Details

Specifications
Thread Size1/2-13
CoatingNo Finish
Wire Insert SeriesLocking
Wire Insert TypeTanged
MaterialStainless Steel
Material304 Stainless Steel
Length Nominal Dia.1 Dia.
Material SpecificationAS7245
Number of Free Coils4-7/8
Free Coil Diameter Min..597 in
Free Coil Diameter Max..622 in
Finish Specificationn/a
Finish AppearanceDyed Red
 
Locking Torque Data
Locking Torque Max.150 in·lb
Locking Torque Min. 15th Cycle24.0 in·lb
 
Drilling Data
Suggested Drill Size ~ Aluminum33/64
Suggested Drill Size ~ Steel, Magnesium, Plastic17/32
Minimum Drilling Depth for Bottoming Taps.808 in
Minimum Drilling Depth for Plug Taps.962 in
Drilling InformationThe minimum drilling depths shown below allow for the following recommended practices: 1. Countersinking the drilled hole to prevent a feather edge at the start of the tapped hole. 2. 3/4 - 1-1/2 pitch of insert ""set-down"" to allow for maximum production tolerance. Dimensions are shown for both plug and bottoming taps. (Note: Plug taps 5/16"" and smaller have a male center and the drilled hole depth dimensions allow for this length (one half of the diameter of the holt). Calculation of dimension ""F"" is as follows For Plug Taps 5/16"" and smaller: F = Insert Nominal Length (Q) + .5 (Bolt Nominal Diameter) + 4P (Tap Chamfer) + 1P (allowance for countersink and maximum insert set-down). For Plug Taps 3/8"" and larger: F = Insert Nominal Length(Q) + 4P (Tap Chamfer) + 1P (allowance for countersink and maximum insert set-down). For Bottoming Taps: F = Insert Nominal Length (Q) + 2P (Tap Chamfer) + 1P (allowance for countersink and maximum insert set-down).
 
Tapping Data
Countersink Diameter Min..590 in
Countersink Diameter Max..620 in
Pitch Diameter Min..550 in
Pitch Diameter Max. ~ Class of Fit 3B_in.554 in
Pitch Diameter Max. ~ Class of Fit 2B_in.555 in
Minimum Tapping Depth.580 in
Tap Major Diameter Max..604 in
 
Taps & Gages
Tap High Spiral Flute Bottoming 2B6905-8
Tap High Spiral Flute Bottoming 3B5905-8
Tap Roughing8CRU
Tap Spiral Point Plug 2B8CSA
Tap Spiral Point Plug 3B8CSB
Tap Straight Flute Bottoming 2B8CBA
Tap Straight Flute Bottoming 3B8CBB
Tap Straight Flute Plug 2B8CPA
Tap Straight Flute Plug 3B8CPB
Reference Gage 2B1440-8
Reference Gage 3B1688-8
Working Gage 2B3688-8
Working Gage 3B1442-8