• Home
  • 3585-7CN656 Tanged Locking Insert

3585-7CN656 Tanged Locking Insert

SKU: 20125 | MPN: 3585-7CN656
/ Eaches
Subtotal:$1.34
Quantity Available *
QuantityLocation
829Bolingbrook
WARNING: Cancer and Reproductive Harm --
P65Warnings.ca.gov
Discount by: unit
QuantityPrice
1 - 249
250 - 499
500 - 999
1,000 - 2,999
3,000 - 4,999
5,000 - 9,999
10,000 - 24,999
25,000 - 49,999
50,000 +
*Additional inventory may be available. Please contact your sales location.

Details

Specifications
Thread Size7/16-14
CoatingNo Finish
Wire Insert SeriesLocking
Wire Insert TypeTanged
MaterialStainless Steel
Material304 Stainless Steel
Length Nominal Dia.1-1/2 Dia.
Material SpecificationAS7245
Number of Free Coils7-3/8
Free Coil Diameter Min..526 in
Free Coil Diameter Max..551 in
Finish Specificationn/a
Finish AppearanceDyed Red
 
Locking Torque Data
Locking Torque Max.100 in·lb
Locking Torque Min. 15th Cycle16.5 in·lb
 
Drilling Data
Suggested Drill Size ~ Aluminum29/64
Suggested Drill Size ~ Steel, Magnesium, Plastic29/64
Minimum Drilling Depth for Bottoming Taps.943 in
Minimum Drilling Depth for Plug Taps1.086 in
Drilling InformationThe minimum drilling depths shown below allow for the following recommended practices: 1. Countersinking the drilled hole to prevent a feather edge at the start of the tapped hole. 2. 3/4 - 1-1/2 pitch of insert ""set-down"" to allow for maximum production tolerance. Dimensions are shown for both plug and bottoming taps. (Note: Plug taps 5/16"" and smaller have a male center and the drilled hole depth dimensions allow for this length (one half of the diameter of the holt). Calculation of dimension ""F"" is as follows For Plug Taps 5/16"" and smaller: F = Insert Nominal Length (Q) + .5 (Bolt Nominal Diameter) + 4P (Tap Chamfer) + 1P (allowance for countersink and maximum insert set-down). For Plug Taps 3/8"" and larger: F = Insert Nominal Length(Q) + 4P (Tap Chamfer) + 1P (allowance for countersink and maximum insert set-down). For Bottoming Taps: F = Insert Nominal Length (Q) + 2P (Tap Chamfer) + 1P (allowance for countersink and maximum insert set-down).
 
Tapping Data
Countersink Diameter Min..520 in
Countersink Diameter Max..550 in
Pitch Diameter Min..484 in
Pitch Diameter Max. ~ Class of Fit 3B_in.488 in
Pitch Diameter Max. ~ Class of Fit 2B_in.489 in
Minimum Tapping Depth.730 in
Tap Major Diameter Max..534 in
 
Taps & Gages
Tap High Spiral Flute Bottoming 2B6905-7
Tap High Spiral Flute Bottoming 3B5905-7
Tap Roughing7CRU
Tap Spiral Point Plug 2B7CSA
Tap Spiral Point Plug 3B7CSB
Tap Straight Flute Bottoming 2B7CBA
Tap Straight Flute Bottoming 3B7CBB
Tap Straight Flute Plug 2B7CPA
Tap Straight Flute Plug 3B7CPB
Reference Gage 2B1440-7
Reference Gage 3B1688-7
Working Gage 2B3688-7
Working Gage 3B1442-7