• Home
  • 1185-10CN938 Tanged Non-Locking Insert, 5/8-11; Stainless Steel; 1-1/2 Dia.

1185-10CN938 Tanged Non-Locking Insert, 5/8-11; Stainless Steel; 1-1/2 Dia.

SKU: 03157 | MPN: 1185-10CN938
/ Eaches
Subtotal:$1.38
WARNING: Cancer and Reproductive Harm --
P65Warnings.ca.gov
Discount by: unit
QuantityPrice
1 - 249
250 - 499
500 - 999
1,000 - 2,999
3,000 - 4,999
5,000 - 9,999
10,000 - 24,999
25,000 - 49,999
50,000 +
*Additional inventory may be available. Please contact your sales location.

Details

Specifications
Thread Size5/8-11
CoatingNo Finish
Wire Insert SeriesNon-Locking
Wire Insert TypeTanged
MaterialStainless Steel
Material304 Stainless Steel
Length Nominal Dia.1-1/2 Dia.
Material SpecificationAS7245
Number of Free Coils8-1/2
Free Coil Diameter Min..742 in
Free Coil Diameter Max..767 in
Finish Specificationn/a
 
Drilling Data
Suggested Drill Size ~ Aluminum21/32
Suggested Drill Size ~ Steel, Magnesium, Plastic21/32
Minimum Drilling Depth for Bottoming Taps1.301 in
Minimum Drilling Depth for Plug Taps1.483 in
Drilling InformationThe minimum drilling depths shown below allow for the following recommended practices: 1. Countersinking the drilled hole to prevent a feather edge at the start of the tapped hole. 2. 3/4 - 1-1/2 pitch of insert ""set-down"" to allow for maximum production tolerance. Dimensions are shown for both plug and bottoming taps. (Note: Plug taps 5/16"" and smaller have a male center and the drilled hole depth dimensions allow for this length (one half of the diameter of the holt). Calculation of dimension ""F"" is as follows For Plug Taps 5/16"" and smaller: F = Insert Nominal Length (Q) + .5 (Bolt Nominal Diameter) + 4P (Tap Chamfer) + 1P (allowance for countersink and maximum insert set-down). For Plug Taps 3/8"" and larger: F = Insert Nominal Length(Q) + 4P (Tap Chamfer) + 1P (allowance for countersink and maximum insert set-down). For Bottoming Taps: F = Insert Nominal Length (Q) + 2P (Tap Chamfer) + 1P (allowance for countersink and maximum insert set-down).
 
Tapping Data
Countersink Diameter Min..730 in
Countersink Diameter Max..760 in
Pitch Diameter Min..684 in
Pitch Diameter Max. ~ Class of Fit 3B_in.688 in
Pitch Diameter Max. ~ Class of Fit 2B_in.690 in
Minimum Tapping Depth1.030 in
Tap Major Diameter Max..748 in
 
Taps & Gages
Tap High Spiral Flute Bottoming 2Bn/a
Tap High Spiral Flute Bottoming 3Bn/a
Tap Roughing10CRU
Tap Spiral Point Plug 2Bn/a
Tap Spiral Point Plug 3Bn/a
Tap Straight Flute Bottoming 2B20187-10
Tap Straight Flute Bottoming 3B10187-10
Tap Straight Flute Plug 2B18187-10
Tap Straight Flute Plug 3B8187-10
Reference Gage 2B1440-10
Reference Gage 3B1688-10
Working Gage 2Bn/a
Working Gage 3Bn/a