• Home
  • 1084-6CNPF090 Tanged Non-Locking Insert, M6X1; Stainless Steel; Primer Free® II; 1-1/2 Dia.; Bulk

1084-6CNPF090 Tanged Non-Locking Insert, M6X1; Stainless Steel; Primer Free® II; 1-1/2 Dia.; Bulk

SKU: 39037 | MPN: 1084-6CNPF090
/ Eaches
Subtotal:$0.46
Quantity Available *
QuantityLocation
3,962Bolingbrook
WARNING: Cancer and Reproductive Harm --
P65Warnings.ca.gov
Discount by: unit
QuantityPrice
1 - 249
250 - 499
500 - 999
1,000 - 2,999
3,000 - 4,999
5,000 - 9,999
10,000 - 24,999
25,000 - 49,999
50,000 +
*Additional inventory may be available. Please contact your sales location.

Details

Specifications
Thread SizeM6X1
CoatingPrimer Free® II
Wire Insert SeriesNon-Locking
Wire Insert TypeTanged
MaterialStainless Steel
Material304 Stainless Steel
Length Nominal Dia.1-1/2 Dia.
Material SpecificationAS7245
Number of Free Coils6-3/4
Free Coil Diameter Min.7.40 mm
Free Coil Diameter Max.7.95 mm
Finish SpecificationRoHS compliant; contains no chromates
Finish AppearanceMatte Black
 
Drilling Data
Minimum Drilling Depth for Bottoming Taps13.00 mm
Minimum Drilling Depth for Plug Taps18.00 mm
Drilling InformationThe minimum drilling depths shown below allow for the following recommended practices: 1. Countersinking the drilled hole to prevent a feather edge at the start of the tapped hole. 2. 3/4 - 1-1/2 pitch of insert "set-down" to allow for maximum production tolerance. Dimensions are shown for both plug and bottoming taps. (Note: Plug taps M8 and smaller have a male center and the drilled hole depth dimensions allow for this length (one half of the diameter of the holt). Calculation of dimension "F" is as follows: For Plug Taps M8 and smaller: F = Insert Nominal Length (Q) + .5 (Bolt Nominal Diameter) + 4P (Tap Chamfer) + 1P (allowance for countersink and maximum insert set-down). For Plug Taps M10 and larger: F = Insert Nominal Length(Q) + 4P (Tap Chamfer) + 1P (allowance for countersink and maximum insert set-down). For Bottoming Taps: F = Insert Nominal Length (Q) + 2P (Tap Chamfer) + 1P (allowance for countersink and maximum insert set-down).
 
Tapping Data
Countersink Diameter Min.7.10 mm
Countersink Diameter Max.7.70 mm
Pitch Diameter Min.6.65 mm
Pitch Diameter Max. ~ Class of Fit 4H_mm6.72 mm
Pitch Diameter Max. ~ Class of Fit 5H_mm6.74 mm
Minimum Tapping Depth10.00 mm
Tap Major Diameter Max.7.42 mm
 
Taps & Gages
Tap High Spiral Flute Bottoming 4H5H5081-6
Tap High Spiral Flute Bottoming 5H4681-6
Tap Spiral Point Plug 4H5H4863-6
Tap Spiral Point Plug 5H4763-6
Tap Straight Flute Bottoming 4H5H4693-6
Tap Straight Flute Bottoming 5H2093-6
Tap Straight Flute Plug 4H5H4687-6
Tap Straight Flute Plug 5H2087-6
Reference Gage 4H4624-6
Reference Gage 5H1324-6