• Home
  • 1084-2.5EN038 Tanged Non-Locking Insert, M2.5X0.45; Nitronic 60; 1-1/2 Dia.; Bulk

1084-2.5EN038 Tanged Non-Locking Insert, M2.5X0.45; Nitronic 60; 1-1/2 Dia.; Bulk

SKU: 60201 | MPN: 1084-2.5EN038
/ Eaches
Subtotal:$1.65
Quantity Available *
QuantityLocation
703Bolingbrook
1,333Morgan Hill
WARNING: Cancer and Reproductive Harm --
P65Warnings.ca.gov
Discount by: unit
QuantityPrice
1 - 249
250 - 499
500 - 999
1,000 - 2,999
3,000 - 4,999
5,000 - 9,999
10,000 - 24,999
25,000 - 49,999
50,000 +
*Additional inventory may be available. Please contact your sales location.

Details

Specifications
Thread SizeM2.5X0.45
CoatingNo Finish
Wire Insert SeriesNon-Locking
Wire Insert TypeTanged
MaterialNitronic
MaterialNitronic 60
Length Nominal Dia.1-1/2 Dia.
Material SpecificationAlloy number UNS S21800
Number of Free Coils5-3/4
Free Coil Diameter Min.3.20 mm
Free Coil Diameter Max.3.70 mm
Finish Specificationn/a
 
Drilling Data
Minimum Drilling Depth for Bottoming Taps5.55 mm
Minimum Drilling Depth for Plug Taps7.70 mm
Drilling InformationThe minimum drilling depths shown below allow for the following recommended practices: 1. Countersinking the drilled hole to prevent a feather edge at the start of the tapped hole. 2. 3/4 - 1-1/2 pitch of insert "set-down" to allow for maximum production tolerance. Dimensions are shown for both plug and bottoming taps. (Note: Plug taps M8 and smaller have a male center and the drilled hole depth dimensions allow for this length (one half of the diameter of the holt). Calculation of dimension "F" is as follows: For Plug Taps M8 and smaller: F = Insert Nominal Length (Q) + .5 (Bolt Nominal Diameter) + 4P (Tap Chamfer) + 1P (allowance for countersink and maximum insert set-down). For Plug Taps M10 and larger: F = Insert Nominal Length(Q) + 4P (Tap Chamfer) + 1P (allowance for countersink and maximum insert set-down). For Bottoming Taps: F = Insert Nominal Length (Q) + 2P (Tap Chamfer) + 1P (allowance for countersink and maximum insert set-down).
 
Tapping Data
Countersink Diameter Min.2.90 mm
Countersink Diameter Max.3.40 mm
Pitch Diameter Min.2.79 mm
Pitch Diameter Max. ~ Class of Fit 4H_mm2.83 mm
Pitch Diameter Max. ~ Class of Fit 5H_mm2.85 mm
Minimum Tapping Depth4.20 mm
Tap Major Diameter Max.3.14 mm
 
Taps & Gages
Tap High Spiral Flute Bottoming 4H5H5081-2.5
Tap High Spiral Flute Bottoming 5H4681-2.5
Tap Spiral Point Plug 4H5H4863-2.5
Tap Spiral Point Plug 5H4763-2.5
Tap Straight Flute Bottoming 4H5H4693-2.5
Tap Straight Flute Bottoming 5H2093-2.5
Tap Straight Flute Plug 4H5H4687-2.5
Tap Straight Flute Plug 5H2087-2.5
Reference Gage 4H4624-2.5
Reference Gage 5H1324-2.5